Kicker 48KMA800.1 Mono-Channel Marine Amplifier

Experience the perfect way to get bass on your boat! A mighty Class-D power plant, 12dB crossover and subsonic filter all help you dial in the best sound. Use the remote level control to adjust the bass right from the dash and connect the full-range RCA outputs to expand your system! Ultra-Efficient Class D Design 1200 Watts of Dynamic Power Mono Amplifier Conformal-Coated Circuit Board KMBLC Remote Level Control Included Variable 12dB Crossover KickEQ™ Variable 6dB Bass Boost Fixed 25Hz Subsonic Filter RCA Pass Through Output Real Marine™ ABYC/NMMA-Compliant Power Connections 316L Stainless-Steel Hardware Included Want setup help" Go to KICKER U for a free woofer-and-amp configuration app! This KM-Series marine amplifier delivers 800 watts into one channel. See below for more details.

Specifications

POWER [watts/ch], 1 OHM MONO: 800 x 1
POWER [watts/ch], 2 OHM MONO: 600 x 1
POWER [watts/ch], 4 OHM MONO: 300 x 1
DYNAMIC POWER [watts]: 1200
COMES WITH WIRED REMOTE" : Yes
Dimensions [in] all models: 2-5/16H x 7-1/8W x 8-1/16L
Dimensions [cm] all models: 5.9H x 18.0W x 20.5L
FREQUENCY RESPONSE [Hz]: 25-200, +0/-1dB
INPUT SENSITIVITY: High Level 250mV-10V - Low Level 125mV-5V
SIGNAL-TO-NOISE RATIO: <95dB, a-weighted, re: rated power
ACTIVE CROSSOVER: 12dB/octave, variable 50-200Hz, low pass only
SUBSONIC FILTER: 24dB/octave, high pass fixed @ 25Hz
KickEQ™ BOOST: Variable 0-6dB, centered @ 40Hz RMS Power test @ 14.4v @ - 1% THD+N, Audio Precision® APx500 analyzer, see www.kicker.com/amp-power-testing for details. Dynamic Power test @ 14.4v @ &ly;/- 10% THD+N, Audio Precision APx500 analyzer, see www.kicker.com/amp-power-testing for details. Audio Precision is a registered trademark of Audio Precision in the United States and other countries.

Diamond Audio MS104SL 10" Marine Subwoofer - 4 Ohm

Specifications Subwoofer Size: 10"
Nominal Impedance (ohms): 4 Ohms
RMS Power Rating: 200W RMS
Max Power Rating: 400W MAX
Mounting Diameter (inch/mm): 9.22” (234.3mm)
Mounting Depth: 4.74” (120.3mm)
Outside Diameter: 10.91” (277.0mm)

Diamond Audio MSPWHR Power/Ground Remote Harness Kit - OFC

Power and Ground Remote Harness Kit with Fusible link and Oxygen free copper (OFC).

Kicker 47KMDB3 Marine Ground Distribution Block

Well Grounded

You need the best possible connection from your amplifiers to ground. That’s why KICKER didn’t re-purpose a car-stereo solution to a marine environment. They created a simple, ABYC-compliant ground block made specifically for your boat. Use the RT-Series ring terminals for the best possible connection.

• Accepts three ground wires
• Compliant to Coast Guard and ABYC standards

Kicker KXMA400.4 4-Channel Marine Amplifier (Certified Refurbished)

KXM Amps are built for the outdoors. Power, speaker and input connections are gasket-sealed, as is the control cover hiding the settings, creating a water-resistant barrier to key controls. The KXM 400-watt four-channel amplifier is flexible enough to be a full system solution, or serve as the power for your mid and high-range speakers. KickEQ+™ delivers as much as an 18dB of extra bump with a simple turn of the knob, and powerful 24dB crossover is also included to letting you quickly tune your system to perfection.

Features

Class D Power Plant
Gain Control With "Optimal Input" Indicator
FIT2™ (Fail-Safe Integration Technology) Circuitry
Variable 24dB Crossover
DSP-Controlled Preamp
KickEQ+™ 18dB Variable Bass Boost
ABYC/NMMA Compliant Power Terminals
Conformal-Coated Circuit Boards
Easy Access to Settings behind Gasket-Sealed Cover Panel
Black Anodized Aluminum Chassis
Top-Mounted Teal LED Light Pipe
Stainless Steel Mounting Hardware Included Want setup help" Go to KICKER U for a free woofer & amplifier configuration app! This KXM amplifier delivers up to 100 watts per channel (4 channels driven), or 200 watts into two sets of bridged channels. See below for more details.

Specifications

RMS Power [Watts]
@ 14.4V, 4Ω stereo, ≤ 1% THD+N: 50 x 4
@ 14.4V, 2Ω stereo, ≤ 1% THD+N: 100 x 4
@ 14.4V, 4Ω bridged mono, ≤ 1% THD+N: 200 x 2 Dimensions [Inches] (L x H x W)
11-3/∕16 x 2-⅛ x 8-5⁄16 Frequency Response [Hz]
10Hz–20kHz Input Sensitivity
250mV–10V Signal-to-Noise Ratio
95dB Selectable Electronic Crossover
Amp 1: OFF/HP/LP; Variable 10–5,000Hz with X10 switch
Amp 2: OFF/HP/LP/BP; Variable HP, 10–500Hz;
Variable LP, 40–5,000Hz with 10X switch
Slope: 24dB/octave KickEQ™ Bass Boost
0-18dB @ 40Hz CEA Power
50 x 4 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006B (Watts) CEA Signal-to-Noise Ratio
-75dB CEA-2006B (ref: 1W, A-weighted)

Polk MM522 MM1 Series 5.25" Car/Marine/Powersports Coaxial Speaker Pair

The Premium Upgrade—tuned to provide the unparalleled sonic accuracy you’ll find in studio monitor speakers, but in a durable, ultra-marine certified design, Polk’s MM1 Series mobilizes high-quality sound for an on-the-go audio upgrade that’s way beyond anything you’ll experience from the stock factory set up in your car, boat, motorcycle or ATV.

Designed to Perform

Every element of the MM Series is meticulously engineered for high-performance sound. Dynamic Balance technology, a pivoting 1” terylene tweeter, lightweight neodymium motor structure, high-temp Conex spiders and oversized voice coils for increased power handling are brought together with 2nd order high and low pass crossovers for optimum system blending—in short, your vehicle might just become your favorite listening environment.

Ultra-Marine Certified

MM1 Series have earned an Ultra-Marine Certified IP56 rating with their non-corrosive aluminum grilles and fiberglass reinforced ABS baskets, epoxy coated crossovers, water-proof inner and outer surrounds, weep holes for proper drainage and titanium-plated cones—that’s all been salt-fog, UV, and humidity tested. With MM1 Series, you get extra, long-lasting protection against virtually anything mother nature can dish out.

Designed to go the Extra Mile

All Polk loudspeakers rely on our patented process to eliminate electro-acoustic and mechanical issues before they become a part of the finished speaker and are also rigorously tested through Polk’s Klippel distortion analyzers. MM1 Series, in addition to their IP56 waterproof rating and Ultra-Marine Certification feature Santoprene S Roll inner and outer surrounds to eliminate water, dirt and dust from entering the speaker housing. maximize throw, and withstand abuse from marine cleaning agents.

Waterproof Santoprene Surrounds

This attractive high performance material maximizes throw with its ultra-flexible, ultra-durable properties—and prevents the elements from entering the speaker unit. Plus, it combats the harsh effects of boat cleaning agents. Advanced High-Performance Sound
Every element of the MM1 Series is meticulously engineered for high-performance sound—Dynamic Balance technology, a pivoting 1” Terylene tweeter, UV tolerant titanium plated composite cones, lightweight neodymium motor structure—plus, glass fiber formers, oversized voice coils and high-temp Conex spiders for increased power handling. Dynamic Balance Technology
Enjoy a rich, clean, full-range sound with our patented Dynamic Balance technology engineered into every MM1 speaker. Rigorously tested and developed by our talented Polk Audio engineers, whose passion rests in the principles of great sound, Dynamic Balance technology features non-resonant materials so you get extremely clear highs, mids and lows no matter what you’re listening to. Integrated Epoxy Coated Crossovers
With its second order high/low pass system, you’re ensured the right frequencies reach the right speakers in your setup for optimal system blending regardless of the vehicle you’re in or the elements you encounter.

Specifications

Coaxial Speakers
Total Pieces: 2
Included Accessories:
• (2) Grilles
• (2) Mounting Hardware
• (2) Wiring Harness
Drivers Warranty: 1 years
Original Purchaser Only: Yes
Total Frequency Response: 50 Hz → 40 Hz
Nominal Impedance: 4 ohms
Max Sensitivity (1 watt @ 1 meter): 92 dB
Type: 1st Order (Woofer) 2nd Order (Tweeter) at 5.0 kHz
Peak Power Handling: 300 watts
Power Handling (per channel): 100 watts → 300 watts Dimensions
Driver Complement:
• (1) 5.25" (13.34 cm) d (Round) Dynamic Balance Driver - Mid/Woofer
• (1) 1" (2.54 cm) d (Round) Pivoting Terylene Tweeter - Tweeter
Shape: Round
Diameter: 4.6" (11.68 cm)
Full-Range Mounting Depth - Top Mount: 2.36" (5.99 cm)
Full-Range Mounting Depth - Bottom Mount: 2.56" (6.5 cm)
Shape: Round
Depth: 0.92" (2.34 cm)

THINKWARE M1 Dual Channel 1080P Dash Cam for Motorcycles, ATVs and UTVs

Whether you are a motorcycle enthusiast or a backcountry explorer on an ATV, the versatile Thinkware M1 Motorsports Cam is a 1080p all-terrain camera you can install on your vehicle to capture all of your adrenaline-filled motorsports adventures. Enjoy your ride without fear of rain, dust, or mud, thanks to the M1’s rugged & weatherproof IP66-rated body that allows it to withstand any conditions. The advanced Electronic Image Stabilization ensures you get smooth and steady video recordings, making shaky footage due to bumpy roads and vibrations a thing of the past. Conquer your ride with the M1 Motorsports Cam alongside you.

Starvis

Outstanding Visability under the Starlight

Super Night Vision 2.0

Super Night Vision technology reduces noise and enhances image quality in low-light conditions.

Video Quality

THINKWARE Dash Cams capture everything from the ordinary to the spectacular

What's in the Box

Front View Camera
Rear View Camera
Main Unit & Remote Control
Mounts (2ea)
Spare 3M Mounting Tapes
32GB MicroSD Card
Quick Start Guide

Installation Sugestions